

.jpg?mode=pad&width=600&height=600)
.jpg?mode=pad&width=600&height=600)
.jpg?mode=pad&width=600&height=600)
.jpg?mode=pad&width=600&height=600)
.jpg?mode=pad&width=600&height=600)
.jpg?mode=pad&width=600&height=600)
.jpg?mode=pad&width=600&height=600)
.jpg?mode=pad&width=600&height=600)
.jpg?mode=pad&width=600&height=600)
.jpg?mode=pad&width=600&height=600)
.jpg?mode=pad&width=600&height=600)
.jpg?mode=pad&width=600&height=600)
.jpg?mode=pad&width=600&height=600)
.jpg?mode=pad&width=600&height=600)
Series
Serie MICRO Standard
Landing doors Compatible

Partial

Complete
Field of application

RESIDENTIAL LIFTS

PUBLIC LIFTS

SPECIAL LIFTS

MODERNIZATION OF OLD LIFT INSTALLATIONS
Features
COMPLIANCE WITH THE REFERENCE STANDARDS
Available

Directive 2014/33/EU on the harmonization of the laws of the Member States relating to lifts and safety components for lifts.

Safety rules for the construction and installation of electric lifts (applies to lifts with compliance tested up to 31 August 2017)

Safety rules for the construction and installation of hydraulic lifts (applies to lifts with compliance tested up to August 31, 2017)

Safety rules for the construction and installation of passenger and goods passenger lifts (applies to lifts with compliance tested starting from September 1, 2017)

Safety rules for the construction and installation of new lifts in existing buildings

Safety rules for the construction and installation of electric lifts with inclined path

Safety rules for the construction and installation of Vertical lifting platforms intended for use by persons with impaired mobility

Safety rules for the construction and installation of lifts, with particular attention to accessibility for persons with disability
On demand
Safety rules for the construction and installation of firefighters lifts (lifts to be used by the firefighters in the event of a fire)
On demand
Safety rules for the construction and installation of lifts, with particular attention to the behaviour of lifts in the event of fire

Safety rules for the construction and installation of lifts subject to seismic conditions
CERTIFICATIONS
Available

Marking for the "safety components" which are compliant with the safety requirements laid down by the directives or by the applicable EU-regulations.
ROLLERS E REINFORCING ELEMENTS FOR THE CAR DOORS
Available

For low and medium-traffic, for standard panels (sliding rollers with 44 mm diameter and truck sliding rails with 40x10 mm thick section)
On demand
For medium and high-traffic, for standard panels (sliding rollers with 67 mm diameter and truck sliding rails with 40x10 mm thick section)
On demand
For medium and high-traffic, for heavy panels (high mechanical resistance plastic sliding rollers with 67 mm diameter and truck sliding rails with 40x10 mm thick section with stiffeners)

For high-traffic, heavy duty and hi-rise installations, for heavy panels (high mechanical resistance plastic sliding rollers with 90 mm diameter and truck sliding rails with 70x14 mm thick section with stiffeners)
ELECTRICAL CONTACTS IP RATING IEC EN 60529/1997 (ex IEC 70-1)
Available
On demand
Protection against water or rain drips falling at an angle up to 60° from the vertical line
On demand
Protection against dust (no harmful deposits) and spraying water from all directions
On demand
Protection against dust (no harmful deposits) and jets of water from all directions

Total protection against dust and against the effects of temporary immersion in water
BASIC DOOR FEATURES
Available

The drive motor and the control drive are factory pre-wired in order to make installation and electrical connection of the car door operator easier

Motor control electronic drive; various power supply options are available in order to meet different Customer needs

The operating parameters of the operator control drive are factory-set, according to door type and size as well as panels weight. Afterwards, the parameter can be changed by means of the programming tool (Optional)

The safety contacts have slots in order to achieve a perfect adjustment and correct any misalignments at the end of the assembly

Vertical position of the retractable coupling cam which can be adjusted according to the position of the landing door hanger

The adjustment systems allows for proper positioning of the panels in regard to the frame and the sliding sill

They ensure free gliding of the panels while improving noiselessness during the opening and closing cycle of the door

It is an uninterrupted connection steel plate below the car door sill. It is a safety device because it prevents any risk of passengers slipping into the shaft during evacuation from the cabin in case of an electrical black-out

Product assembly and adjustment manual. Safety information included.
AVAILABLE OPTIONS FOR THE PANELS
Available
On demand
Cladding with different kinds of materials and finishings (stainless steel, plastic-film coated steel, plastic laminated steel, etc.), only applied to the surfaces which are visible from inside the cabin (not for Serie DIAMOND panels)
On demand
Cladding with different kinds of materials and finishings (stainless steel, plastic-film coated steel, plastic laminated steel, etc.), only applied to the surfaces which are visible from the landing and from inside the shaft (not for Serie DIAMOND panels)
On demand
Panels in special execution designed according to the kind of cladding that the Customer wants to use (not for Serie DIAMOND panels)
On demand
Semi-gloss paint with smooth finish or semi-gloss paint orange-peel finish, only applied to the surfaces which are visible from inside the cabin (not for Serie DIAMOND panels)
On demand
Semi-gloss paint with smooth finish or semi-gloss paint orange-peel finish, only applied to the surfaces which are visible from the landing and from inside the cabin (not for Serie DIAMOND panels)
On demand
Frame surfaces treated by electrophoretic deposition or painted with anti-corrosion paint for use in case of saline mist or in saline environment (not for Serie DIAMOND panels)
On demand
Panels made of AISI 304 or AISI 316 "food" stainless steel, for use in highly corrosive environments (not for Serie DIAMOND panels)
On demand
Panel double-plating towards the landing, made of iron plate painted RAL 7038 light orange-peel finish. The panel double-plating can be cladded or finished like the surfaces which are visible from the cabin (not for Serie DIAMOND panels)
On demand
Panel double-plating towards the inside of the landing, made of iron plate painted RAL 7038 light orange-peel finish, filled with rockwool. The panel double-plating can be cladded or finished like the surfaces which are visible from inside the cabin
On demand
Panels made of iron or stainless steel plate with wider slam edge in order to compensate for size differences with the sill (special sill with extended width)
On demand
Panels with safety glass vision panel (100 x H 300 or 100 x H 600 mm), various cladding materials and surface finishings available (stainless steel, plastic-film coated steel, painted, etc.)

Panoramic glass-framed panels with laminated safety glass and metal frame, available in various materials and finishings (stainless steel, plastic-film coated steel, painted, etc.)

Panoramic full glass panels (without metal frame) with tempered safety glass with upper and bottom fixings in natural color stainless steel and transparent neutral color methacrylate slam edge profile
On demand
The system consists of a fixed cam, installed on the inner side of the car door panel, which releases the lock of the manual landing swing door
ADD-ONS AND OPTIONS FOR CAR DOOR OPERATORS
Available
On demand
Some car door operator models are equipped with the motor placed vertically as a standard. This options reduces the vertical place requirement of the operator in case of low shaft headroom
On demand
With this option the motor can be installed symmetrically in respect to the standard position, this is especially useful in case of a tight fit between the motor itself and the other components installed on the cabin roof
On demand
In case of lifts with especially low headroom, it is possible to reduce the vertical place requirement for the car door operator
On demand
The coupling cam of the car door operator can be customized in order to operate landing door hangers with locks in special execution and different from the PRISMA standard ones
On demand
The car door operator can be equipped with a coupling system with fixed cam or C-Profile in order to operate landing door hangers with locks in special execution and different from the PRISMA standard ones
On demand
As a standard, the car door operator is equipped with an electrical safety contact which confirms the closed status of the door. An additional safety contact can be supplied for position control of the panels sliding truck upon request
On demand
Mechanical lock electrically controlled which ensures that the car door operator stays closed during travel between the floors. Compliant with the requirements of the EN81-20/50 European Standards
On demand
The device is automatically activated by the car door operator in order to release the lock of the manual landing swing door. The device is available with different pushing directions
On demand
Coupling system with fixed cam installed on the operator sliding truck which releases the lock of the manual landing swing door
On demand
In case of an electrical black-out the buffer batteries enable the opening of the doors and the passengers evacuation from the cabin
On demand
Useful feature which ensures the proper functioning of the doors at low temperatures outdoors or inside cold stores. A thermostat-measures the temperature and switches the heating system on when the set limit has been reached
On demand
Steel plate enclosure which almost completely covers the mechanical and moving components of the hanger. Its function is mainly aesthetic, but it also provides partial protection to the hanger itself. Available in various materials and finishings
On demand
Qualora esista il rischio di caduta di liquidi o di materiale sabbioso all'interno del vano di corsa dell'ascensore, con conseguente rischio di danno per i componenti dislocati sul tetto della cabina, sono disponibili carter di protezione in lamiera o in plexiglas trasparente per il Drive di pilotaggio
On demand
Programming tool for customizing of the opening and closing door movement settings. Can be used to adjust various parameters, such as acceleration, maximum speed, deceleration, torque, etc., with different values for the opening and closing setting profiles
On demand
They are mainly used in order to stiffen the connection between the panels and the car door operator. They are designed for the coupling with panels with special geometry for special applications or modernizations (pre-existing panels)
On demand
PRISMA can supply various models of electronic light curtains for passenger safety during cabin access. The detectors can be installed in fixed position, between the car door operator and the sill, or on the panel slam edge or on the cabin shoulder
On demand
Support kit for installation of the light curtain between the car door operator and the sill, in a hidden and safe position
On demand
Supplied as a special option, essential in lift shafts with very low pit and where the standard 750 mm toe-guard cannot be used. The slide-out IES toe-guard is installed below the cabin floor and it is pulled out in order to evacuate the passengers from the cabin in complete safety in case of an electrical black-out
POWER SUPPLY
Available
On demand
Direct or alternate current power supplies units, with special tension or frequency are available upon request
AVAILABLE OPTIONS FOR THE SILLS
Available
On demand
Reinforced sill aluminium profile with enlarged cross-section for small loads
On demand
Sill profile in Stainless Steel, available in various electro-colored finishings. For passenger lifts
On demand
Sill profile for goods lifts with capacity up to 3000 kg, made of tubular iron profiles, painted in black color or in other colors upon request
On demand
Sill profile for goods lifts with capacity up to 3000 kg, made of tubular iron profiles, electro-galvanized
On demand
Sill profile for goods lifts with capacity up to 3000 kg, made of AISI 304 Stainless Steel tubular profiles
On demand
Sill profile for goods lifts with capacity up to 3000 kg, made of AISI 316 Stainless Steel tubular profiles
On demand
Sill profile for large goods lifts with capacity over 3000 kg, made of solid-drawn iron profiles, painted black or in other colors upon request
On demand
Sill profile for large goods lifts with capacity over 3000 kg, made of solid-drawn iron profiles, electro-galvanized
On demand
Sill profile for large goods lifts with capacity over 3000 kg, made of AISI 304 Stainless Steel solid-drawn profiles
On demand
Sill profile for large goods lifts with capacity over 3000 kg, made of AISI 316 Stainless Steel solid-drawn profiles
On demand
Special sill profile placed below the floor level, in a hidden area. It is an aesthetic solution which ensures an uninterrupted even surface between the landing and cabin floor
On demand
Useful feature which ensures the proper functioning of the doors at low temperatures outdoors or inside cold stores. A thermostat-measures the temperature and switches the heating system on when the set limit has been reached
PACKING OPTIONS
Available
On demand
Special packaging in wooden box with interior lined with bituminous paper
On demand
Special packaging compliant with ISPM15 Standards, which lay down phytosanitary measures to prevent the spread of harmful organisms among different continents. The Standards apply to wooden packaging for export to some Extra-European countries
On demand
Special customized packaging made on specific request by the Customer
PANELS FINISHINGS
Available

Epoxy powder semi-gloss paint with light orange-peel finish, highly abrasion resistant, suitable for indoors (not for Serie DIAMOND panels)
On demand
Very robust and strong hot-dip galvanized fire-painted steel, coated with removable transparent PVC protective film (not for Serie DIAMOND panels)
On demand
Semi gloss paint orange-peel finish, available in a wide range of colors, some colors are immediately available and others can be supplied upon request (not for Serie DIAMOND panels)
On demand
Semi gloss paint smooth finish, available in a wide range of colors, some colors are immediately available and others can be supplied upon request (not for Serie DIAMOND panels)
On demand
Special paint fur use in highly corrosive environments such as chemical and food industry or for outdoors installations in saline environment (not for Serie DIAMOND panels)
On demand
AISI 430 Stainless steel version (for indoors) available in Satin or Scotch-Brite surface finishing, used as cladding material to be applied over the structural elements of the panels or directly for self-bearing construction of such elements (not for Serie DIAMOND panels)
On demand
AISI 304 Stainless steel version (for both indoors and outdoors) available in Satin or Scotch-Brite surface finishing (some models also available in colored version), used as cladding material to be applied over the structural elements of the panels or directly for self-bearing construction of such elements (not for Serie DIAMOND panels)
On demand
AISI 316 Stainless steel version (for outdoors, indoors and for highly corrosive environments) available in Satin or Scotch-Brite surface finishing, used as cladding material to be applied over the structural elements of the panels or directly for self-bearing construction of such elements (not for Serie DIAMOND panels)
On demand
AISI 304 Stainless steel version (for both indoors and outdoors) with Patterned surface finishing (various surface patterns as well as different colors are available for some models), used as cladding material to be applied over the structural elements of the panels or directly for self-bearing construction of such elements (not for Serie DIAMOND panels)
On demand
AISI 316 Stainless steel version (for outdoors, indoors and for highly corrosive environments) with Patterned surface finishing (various surface patterns are available), used as cladding material to be applied over the structural elements of the panels or directly for self-bearing construction of such elements (not for Serie DIAMOND panels)
On demand
AISI 304 Stainless steel version (for the chemical and food industry, for outdoors, indoors and for corrosive environments) available in various surface finishings, used as cladding material to be applied over the structural elements of the panels or directly for self-bearing construction of such elements (not for Serie DIAMOND panels)
On demand
AISI 316 Stainless steel version (for the chemical and food industry, for outdoors, indoors and for highly corrosive environments) available in various surface finishings, used as cladding material to be applied over the structural elements of the panels or directly for self-bearing construction of such elements (not for Serie DIAMOND panels)
On demand
Galvanized iron plate coated in plastic film available in various surface finishing, used as cladding material to be applied over the structural elements of the panels or directly for self-bearing construction of the panels (not for Serie DIAMOND panels)
On demand
Brass sheets are used as cladding for the panels structural elements. It is available with polished or satin finish, rough or with anti-oxidation surface treatment (not for Serie DIAMOND panels)
On demand
Copper sheets are used as cladding for the panels structural elements. It is available with semi-polished or satin finish, rough or with anti-oxidation surface treatment (not for Serie DIAMOND panels)
On demand
Corten Weathering Steel (CORrosion resistance + TENsile strength) is a material which exhibits very high self-protection capacity against electrochemical corrosion. It is used as cladding for the structural elements of the panels and it can be supplied rough or with transparent paint coating or waxed (nit for Serie DIAMOND panels)
On demand
Raw iron is often used as a finishing element in industrial design. For doors it is used as cladding for the structural elements of the panels and it can be supplied with rough blackened or pickled surface finishing, with or without transparent anti-corrosion surface coating (not for Serie DIAMOND panels)
On demand
The laminated plastic steel plate is only used for cladding of the panels. The material is available as flat sheet and requires holding profiles on the panel side edges. The laminated plastic steel plate is available in various patterns and colors and the holding profiles are also available in various materials and finishings (not for DIAMOND panels)
FINISHINGS FOR CAR DOOR OPERATORS
Available
On demand
Highly protective coating which provides very high corrosions resistance
On demand
Semi gloss paint smooth finish, available in a wide range of colors, some colors are immediately available and others can be supplied upon request
On demand
The main components (baseplate, sliding trucks, sliding guides, etc.) are made of AISI 304 Stainless Steel (for chemical and food industry, for outside installations, for interiors as well as corrosive environments)
On demand
The main components (groundplate, sliding trucks, sliding guides, etc.) are made of AISI 316 Stainless Steel (for chemical and food industry, for outside installations, for interiors as well as especially corrosive environments)
Documentation
Technical Documents
Technical Catalogue
Technical Circular Letters
Instructions
INSTALLATION LAYOUT - ASSEMBLY INSTRUCTIONS

INSTALLATION LAYOUT - ASSEMBLY INSTRUCTIONS

INSTALLATION LAYOUT - ASSEMBLY INSTRUCTIONS

INSTALLATION LAYOUT - ASSEMBLY INSTRUCTIONS

INSTALLATION LAYOUT - ASSEMBLY INSTRUCTIONS

INSTALLATION LAYOUT - ASSEMBLY INSTRUCTIONS

INSTALLATION LAYOUT - ASSEMBLY INSTRUCTIONS

INSTALLATION LAYOUT - ASSEMBLY INSTRUCTIONS

INSTALLATION LAYOUT - ASSEMBLY INSTRUCTIONS

INSTALLATION LAYOUT - ASSEMBLY INSTRUCTIONS

INSTALLATION LAYOUT - ASSEMBLY INSTRUCTIONS

INSTALLATION LAYOUT - ASSEMBLY INSTRUCTIONS

INSTALLATION LAYOUT - ASSEMBLY INSTRUCTIONS

DIP SWITCH SETTINGS FOR DRIVE FOX WITH CANBus

DIP SWITCH SETTINGS FOR DRIVE FOX WITH CANBus

WIRING DIAGRAM FOR IP67 SENSORS

INSTRUCTION MANUAL - GROUND CONNECTION

INSTRUCTIONS FOR THE ADJUSTMENT OF THE MY15 CAR DOOR LOCK DEVICE

DRIVE FOX - KIT LONG LIFE WIRING DIAGRAM

The selected document requires authentication, Sign in .
If your user role does not match the requirements, you will still not be able to download the selected document.